40-65 mould

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Thread Modes

40-65 mould

12-15-2023, 05:24 PM,

#14

Kurt

Grand advisory committee

Posts: 4,247
Location:
Joined: May 2012
Reputation: 2

RE: 40-65 mould

Steve,

From looking at recovered bullets, mostly PP but also GG and a very hard 1/16 mix of tin, antimony, lead patched .002" under bore diameter they showed up fully engraved into the grooves and no gas cuts.

Also I even loaded 5 with 5744 powder and they also filled the grooves. I know that some say that smokeless don't upset a lead bullet but I see different signs. Big Grin

The reason a dog has so many friends is because he wags his tail instead of his tongue.

Find

« Next Oldest | Next Newest »

Messages In This Thread

40-65 mould - by Steveu - 08-24-2023, 09:02 AM

RE: 40-65 mould - by Kurt - 08-24-2023, 10:05 AM

RE: 40-65 mould - by Don McDowell - 08-24-2023, 11:43 AM

RE: 40-65 mould - by Don McDowell - 08-24-2023, 11:45 AM

RE: 40-65 mould - by Steveu - 08-24-2023, 09:53 PM

RE: 40-65 mould - by Kurt - 08-24-2023, 10:16 PM

RE: 40-65 mould - by Don McDowell - 08-25-2023, 09:03 AM

RE: 40-65 mould - by Kurt - 08-25-2023, 10:21 AM

RE: 40-65 mould - by Don McDowell - 08-25-2023, 11:33 AM

RE: 40-65 mould - by beltfed - 08-25-2023, 11:43 AM

RE: 40-65 mould - by Kurt - 08-25-2023, 02:55 PM

RE: 40-65 mould - by J.B. - 08-25-2023, 09:36 PM

RE: 40-65 mould - by Steveu - 12-15-2023, 10:29 AM

RE: 40-65 mould - by Kurt - 12-15-2023, 05:24 PM

RE: 40-65 mould - by Steveu - 12-18-2023, 12:51 PM

RE: 40-65 mould - by beltfed - 12-21-2023, 12:33 PM

RE: 40-65 mould - by Kurt - 12-21-2023, 01:16 PM

RE: 40-65 mould - by Steveu - 12-22-2023, 12:50 AM

RE: 40-65 mould - by Kurt - 12-22-2023, 12:27 PM

RE: 40-65 mould - by Steveu - 12-22-2023, 01:35 PM

RE: 40-65 mould - by Kurt - 12-22-2023, 03:20 PM

RE: 40-65 mould - by Steveu - 12-23-2023, 05:16 PM

RE: 40-65 mould - by Don McDowell - 01-19-2024, 10:59 AM

RE: 40-65 mould - by Kurt - 01-19-2024, 12:13 PM

RE: 40-65 mould - by Don McDowell - 01-19-2024, 12:51 PM

RE: 40-65 mould - by Kurt - 01-19-2024, 03:20 PM

RE: 40-65 mould - by Don McDowell - 01-19-2024, 04:04 PM

RE: 40-65 mould - by Steveu - 01-25-2024, 03:16 PM

RE: 40-65 mould - by Don McDowell - 01-25-2024, 03:18 PM

RE: 40-65 mould - by Steveu - 01-25-2024, 04:50 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me